I never really used Playlists, so I cannot comment on that, sorry. The only thing I do is subscribing to some channels in Invidious when I am on my PC and I do see them in Kodi. Usually I search for what I am interested in and that works fine for me in Kodi and Invidious. Invidious is still in active development, but you meant the Kodi Plugin maybe? I hope it is not abandoned and just not worked on because it still… works? :-)

I use the Kodi Invidious Plugin and my own Invidious instance.

The .10 or .20 just advises Docker to create that specific Subinterface automatically. In my example ip link will show new interfaces called br0.10 and br0.20 after creating the macvlan networks for VLAN IDs 10 and 20. You do not need to adjust your Netplan config when doing it like that. I would even assume that you are not allowed to define VLAN ID 10 and 20 in that particular case also in Netplan. I would expect that this will cause issues. Also see https://docs.docker.com/engine/network/drivers/macvlan/ in the 802.1Q trunk bridge mode section.

There are probably multiple ways to do all of this, but this is how I did it and it works for me since a few years without touching it again. All VLANs are separated from each other and no VLAN has access to the LAN side. Everything is forced to go through tagged VLANs via the switch to the Firewall, where I then create rules to allow / deny traffic from / to all my networks and the Internet.

For me, this setup is very simple to re-implement should my Host go down. No special configuration in Netplan is needed. Only create the Docker Networks and start up my stacks again.

I can’t see your full setup / config from here, but a) you are not overengineering that. Using VLANs to segment networks is a very good practice. And although Docker (nor Podman) allow macvlan when running rootless, my gutfeeling tells me that segmenting my network takes priority over running rootless, because I think that attack vectors by traversing networks are much more common that breaking out of a container into the host. But this is just my gutfeeling. b) I think I run here what you want to achieve, so I try to explain what I did.

My Setup is similar to yours. OPNsense (OpenWRT before that), a Switch that is capable of VLAN and a Ubuntu Server with a single NIC that hosts all the Compose stacks.

1. You already configured your VLANs in OPNsense, so I will just mention that I created mine via Interface -> Devices -> VLAN on the LAN Interface of my OPNsense and then used the Assignments to finally make them available. On the OPNSense each one gets a static IP from the respective Network I defined for the VLAN.
2. On the Docker Host, in Netplan I configured the single NIC I have as a Bridge. I cannot remember if that was necessary or if I just planned ahead, should I add a 2nd NIC later on, to prevent that I need to reconfigure the whole networking again. Of course that Bridge sits in my LAN and the Netplan Config looks like this:

network:
  ethernets:
    eno1:
      dhcp4: no
  version: 2
  bridges:
    br0:
      addresses:
      - 192.x.x.3/24
      nameservers:
        addresses:
        - 192.x.x.x
        search:
        - my.lan
        - local
      routes:
      - to: default
        via: 192.x.x.1
      interfaces:
        - eno1

3. Now that the Docker Containers can use the VLANs, I had to create Docker Networks as macvlan like this:

docker network create -d macvlan --subnet=192.x.10.0/24 --gateway=192.x.10.1 -o parent=br0.10 vlan10
docker network create -d macvlan --subnet=192.x.20.0/24 --gateway=192.x.20.1 -o parent=br0.20 vlan20

4. Now for a Container to make use of those Networks, you have to define them as External in the Compose Stack like this:

services:
  my-service:
    image: blah
    ...
    networks:
      vlan10:

networks:
  vlan10:
    name: vlan10
    external: true

In 4. you have the option to not define an ipv4_address in the networks section. Then Docker will just pick its own addresses when the containers start. Letting OPNsense assign IP addresses dynamically in such a VLAN is something that did not work for me. So either you let Docker pick the IPs when starting a stack, or you define your IP addresses in the stack. If you do the latter, you have to do it for every stack that ever joins that VLAN, otherwise Docker might pick an IP that you already assigned manually and that stack will not start.

I also wanted to have some services running directly in the LAN via Docker. This setup is a bit more involved and requires you to create a SHIM Network, otherwise the Docker Host itself will not be capable of accessing Containers running in the LAN Network. This was the case for my Pi-Hole for example, that I wanted to have an IP in my LAN Network and had to be reachable by the Docker Host itself too. There is a very good post about Macvlan and SHIM Networks in this blog: https://blog.oddbit.com/post/2018-03-12-using-docker-macvlan-networks/

I hope this helps. Do not give up. Segmenting your Networks is important, especially if you plan to publish some services over the Internet.

Since you are German, don´t forget the Impressum. I think it is mandatory and some people are dicks.

Not exactly what you asked, but for old-school TV I use Tvheadend and it is not a Jellyfin Plugin. Instead, everything (including Jellyfin) plugs into Kodi in our Household and relatives.

• Oldschool TV (Scheduling, Recordings, Live TV) is run via Tvheadend and a USB TV Cable adapter.
• Youtube runs via a self-hosted Invidious instance.
• My own Music lies on a NAS, indexed by Kodi and Jellyfin.
• Some TV Shows and Movies lie also on a NAS indexed by Kodi and Jellyfin.

Media is scattered over various places and services and Kodi pulls them all together.

• TV via Tvheadend=Added to Kodi via the Tvheadend Plugin.
• Youtube/Invidious=Added to Kodi via the Invidious Plugin.
• Jellyfin=Added to Kodi via the Invidious Plugin.
• Other media that´s on the NAS=Added to Kodi via Library scanning.
• Mediathekview=Added to Kodi via the Mediathekview Plugin.

Kodi serves all Media with a unified interface, no matter what it is or where it comes from. When using the TV we see Kodi and we pick what we want to consume.

Additionally, other family members can connect via Wireguard to my network, have one of those old Ex-Android TV Boxes on the TV on which Kodi (CoreElec or Libreelec) with the necessary Plugins is installed and they have the same unified experience. No need to “learn” how to use different UIs / Software for different Media. For the consumer it is all in one place --> Kodi :-)

Thanks for pointing out Simplex Chat, I did not know that it exists. It looks very interesting, but reading more about it, they will have to implement some kind of business model in the future. My fear is, that even when self-hosting, some features will be behind a paywall in the future, so it is not a solution I would switch to… switching to a new messenger is a long-term endeavour. It is hard to convince friends to move over too, let alone switching to a new one every few years. That’s near impossible. But the technology of Simplex looks really interesting and reading through the Docs it makes the impression that it is very polished.

Thank you very much for the technical insight. It makes clear why it is how it is and it is good to see that you can host Activitypub services on Subdomains… so the issue I thought that exists is not that big of an issue anymore. Also I love the discussion under your post, very interesting!

Thanks also to everyone else who replied!